TunerStudio MS 1.0 Released
Moderator: LT401Vette
-
- Experienced MS/Extra'er
- Posts: 213
- Joined: Wed Jan 23, 2008 2:37 am
- Location: The Netherlands
Re: TunerStudio MS 1.0 Released
Update does great!!
I only still get the K version in top of the programm?
Thanks and greetings,
Erik
I only still get the K version in top of the programm?
Thanks and greetings,
Erik
-
- Site Admin
- Posts: 39621
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: TunerStudio MS 1.0 Released
I guess it didn't update then..!
The release says "TunerStudio MS v1.0" in the title bar.
James
The release says "TunerStudio MS v1.0" in the title bar.
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
-
- Super MS/Extra'er
- Posts: 1986
- Joined: Sat Jul 22, 2006 8:02 pm
- Location: Eureka, NV USA
- Contact:
Re: TunerStudio MS 1.0 Released
Win7 starter on a netbook......
I did the auto update from TS and TS wouldn't run anymore! I uninstalled and down loaded 1.0 from the TS site, reinstalled. Voila!! Up and running!!
Works great.
Ken
I did the auto update from TS and TS wouldn't run anymore! I uninstalled and down loaded 1.0 from the TS site, reinstalled. Voila!! Up and running!!
Works great.
Ken
1979 Corvette - 383 CID SBC w/ Holley Pro-Jection 900 CFM TBI, 4-85 lb lo-z injectors & Walbro 255 pump
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
MS2 v3 w/extra 3.4.2 Release
36-1, Delphi LS2/7 coils in wasted spark, driven by v2.0 logic board from JBPerformance
Spartan Lambda Sensor from 14point7
TinyIOX from JBPerformance
-
- Experienced MS/Extra'er
- Posts: 213
- Joined: Wed Jan 23, 2008 2:37 am
- Location: The Netherlands
Re: TunerStudio MS 1.0 Released
It is running now!!!
Re: TunerStudio MS 1.0 Released
Is there a way of rolling back my install version?
I tried running the previous version setup file but the software tells me I have a newer version so it won't install.
I tried running the previous version setup file but the software tells me I have a newer version so it won't install.
Re: TunerStudio MS 1.0 Released
That's weird, I did not have that experience. Downloaded the 0.999.9k setup, ran it, didn't get any errors and it seems to have worked (when I launch TS it now says 0.999.9k in the title bar). This is on Windows XP.
Eric Law
1990 Audi 80 quattro with AAN turbo engine: happily running on MS3+MS3X
2012 Audi A4 quattro, desperately in need of tweaking
Be alert! America needs more lerts.
1990 Audi 80 quattro with AAN turbo engine: happily running on MS3+MS3X
2012 Audi A4 quattro, desperately in need of tweaking
Be alert! America needs more lerts.
Re: TunerStudio MS 1.0 Released
first time i updated it stayed on version k, i did it again and its now 1.0 i dont know whats up with that, but it worked the second time...
95 escort gt BPT - MS2E/ms2extra pre3.3alpha5 gslender v2.8 - E85 - 256/250 on mustang dyno at 10psi, now tuning for gtr turbo
Re: TunerStudio MS 1.0 Released
So today I upgraded to TunerStudio 1.0 to tune my friends MS1, but when I went to the VE Analyze Live tab it just sat on the loading screen. I tried closing the program and same thing happened, and I also created a new project to have the same with happen. I wasn't ever able to load VE Analyze Live and had to downgrade to 0.999.9o.
Re: TunerStudio MS 1.0 Released
One thing I saw now for this new version is that you cannot open several windows, for example Ignition 1 and Ignition 3.
Now, when you have the ignition window open, you cannot check anything else until you close it.
Did you do this change on purpose?
EDIT: From what I tested so far (and not all) only the Engine Constants will alow you to open another window simultaneously.
Now, when you have the ignition window open, you cannot check anything else until you close it.
Did you do this change on purpose?
EDIT: From what I tested so far (and not all) only the Engine Constants will alow you to open another window simultaneously.
Golf II + 1.8T 20V + MSII V3.0 http://eight620vt.tk/
-
- Site Admin
- Posts: 39621
- Joined: Mon May 03, 2004 1:34 am
- Location: Birmingham, UK
- Contact:
Re: TunerStudio MS 1.0 Released
See if you have "modal" enabled.
James
James
I can repair or upgrade Megasquirts in UK. http://www.jamesmurrayengineering.co.uk
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
My Success story: http://www.msextra.com/forums/viewtopic ... 04&t=34277
MSEXTRA documentation at: http://www.msextra.com/doc/index.html
New users, please read the "Forum Help Page".
Re: TunerStudio MS 1.0 Released
~You are absolutely correct!jsmcortina wrote:See if you have "modal" enabled.
James
Not sure why that changes (if it was me, or the upgrade, but I suspect me) but now it's back again.
Thanks!
Golf II + 1.8T 20V + MSII V3.0 http://eight620vt.tk/
-
- Master MS/Extra'er
- Posts: 686
- Joined: Sat Jan 01, 2011 4:42 pm
- Location: Burlington, CT USA
Re: TunerStudio MS 1.0 Released
Awesome! Updating now!
1992 Volvo 740 Wagon - Beater Car...CAI, 16T, catback, MS3/MS3X, & HID's
1996 Eagle Talon TSi AWD - Daily Driver...RAI, Big 16g, 3" TBE, HID's, etc.
1996 Eagle Talon TSi AWD - Daily Driver...RAI, Big 16g, 3" TBE, HID's, etc.
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: TunerStudio MS 1.0 Released
elaw,
if you shut of "Report INI warnings" under the menu:
Options --> Advanced
Those will go away.
if you shut of "Report INI warnings" under the menu:
Options --> Advanced
Those will go away.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: TunerStudio MS 1.0 Released
Running the full version 1.0 up here and works great. Thanks.
-Andrew
-Andrew
-Andrew
Re: TunerStudio MS 1.0 Released
Did you find a fix for this problem? I have the same problem and my inc files are here C:\Users\Owner\Documents\TunerStudioProjects\Turbo_Buggy\incdan187 wrote:Great software, good work.
However, I just updated to v1. Right before the update my temp sensors were correct, after update the software reloaded and the readings are now too low (just as if the calibration is wrong). Could you suggest a solution for me?
I've checked and the inc files are still in the project folder.
Regards
Dan
I looked inside the files and they look correct. I'm assuming TS just doesn't see them any more
Dodge 2.2L MPI Turbo Power Running MSnS1/Extra.
Chevrolet 5.3 LM7 running MSnS2 /Extra
Chevrolet Twin Cam 4 cyl running MSnS2 / Extra
Home of the USB data logger---> http://www.msextra.com/forums/viewtopic ... 67&t=34901
Chevrolet 5.3 LM7 running MSnS2 /Extra
Chevrolet Twin Cam 4 cyl running MSnS2 / Extra
Home of the USB data logger---> http://www.msextra.com/forums/viewtopic ... 67&t=34901
Re: TunerStudio MS 1.0 Released
Thanks so much man. I was finally able to run TS in 15 fps without it wigging out. Job well done.
James
James
'95 Saturn SC2 SC at 15psi
MS2 V3.0 w/MS2 Extra 3.1.1 Firmware
MS2 V3.0 w/MS2 Extra 3.1.1 Firmware
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: TunerStudio MS 1.0 Released
No, but I did some digging and I found a problem that started with 9m. I haven't changed anything there in at least a year and a half, so i didn't think it could be broke, but actually it is. When it does the ini validations the project dir has not yet been set, so it never finds the inc in the project and loads the app one. Then when real data comes in it has the app level once cached.Huey wrote:Did you find a fix for this problem? I have the same problem and my inc files are here C:\Users\Owner\Documents\TunerStudioProjects\Turbo_Buggy\incdan187 wrote:Great software, good work.
However, I just updated to v1. Right before the update my temp sensors were correct, after update the software reloaded and the readings are now too low (just as if the calibration is wrong). Could you suggest a solution for me?
I've checked and the inc files are still in the project folder.
Regards
Dan
I looked inside the files and they look correct. I'm assuming TS just doesn't see them any more
There will be a patch fix out for this tomorrow.
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
Re: TunerStudio MS 1.0 Released
Okay, sounds good
Thanks
Thanks
Dodge 2.2L MPI Turbo Power Running MSnS1/Extra.
Chevrolet 5.3 LM7 running MSnS2 /Extra
Chevrolet Twin Cam 4 cyl running MSnS2 / Extra
Home of the USB data logger---> http://www.msextra.com/forums/viewtopic ... 67&t=34901
Chevrolet 5.3 LM7 running MSnS2 /Extra
Chevrolet Twin Cam 4 cyl running MSnS2 / Extra
Home of the USB data logger---> http://www.msextra.com/forums/viewtopic ... 67&t=34901
Re: TunerStudio MS 1.0 Released
TS 1.001 was auto updated to my PC. Anything new?
Fiat Seicento 1242cc F.I.R.E. engine
VR sensor on 60-2, wasted spark
MS-II Extra pre3.3 a5 Gslender 2.8
VR sensor on 60-2, wasted spark
MS-II Extra pre3.3 a5 Gslender 2.8
-
- Super MS/Extra'er
- Posts: 12733
- Joined: Sat Jul 16, 2005 8:07 am
- Location: Moorseville, NC
- Contact:
Re: TunerStudio MS 1.0 Released
It is in the change log:
http://tunerstudio.com/index.php?option ... &Itemid=61
2 fixes. Loading inc files from the project first and fixed the double pasting of gauges when using CTRL+P
http://tunerstudio.com/index.php?option ... &Itemid=61
2 fixes. Loading inc files from the project first and fixed the double pasting of gauges when using CTRL+P
Phil Tobin
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html
EFI Analytics, helping to simplify EFI
Next Generation tuning software.
Supporting all MegaSquirt versions and firmwares.
http://www.TunerStudio.com
http://www.efiAnalytics.com/MegaLogViewer/
Support the firmware running your engine:
http://www.msextra.com/doc/donations.html